banner



How To Install A Register Vent

Download Article

Download Commodity

Roof vents are devices that allow moisture in your dwelling to escape and prevent the growth of mold and mildew. The most mutual types of vents are soffits, static exhaust vents, and ridge vents that span your entire roof, and you can install all of them easily with a few tools from your local hardware store!

  1. 1

    Check effectually the edges of your attic for any wiring. Become into your attic and look at the area where you lot plan to install your soffits. Movement any insulation around the outer edges and make sure the area is articulate of any electrical components or wiring so you can work safely outside with your power tools. If there are wires, discover a different spot to install your soffits.[1]

    • Drill a hole in the center of where you desire your vent while yous're in the attic so y'all know where to saw later.
  2. ii

    Outline a seven in × xv in (xviii cm × 38 cm) rectangle on your overhang outside. Look for nail lines or seams in the paint since these bespeak where a rafter would be in your attic. Use a pencil and a straightedge to draw the rectangle directly onto the lesser of your overhang. This volition be where y'all put the soffit vent.[2]

    • Use a tall ladder to accomplish a taller overhang. Have a partner concur the ladder steady and then you lot can piece of work safely.
    • Make a template using cardboard that's the width of your overhang with a hole the size of the vent cut in it. This way, you tin easily trace effectually information technology and your vents will be straight.
    • The size of the rectangle will depend on the size of the vents, but a standard size is 8 in × sixteen in (xx cm × 41 cm).

    Advertising

  3. 3

    Drill holes outside in the corners of the rectangle. Use a drill bit large enough so that y'all can fit your saw bract loosely inside the holes it makes. Drill the holes in all 4 corners of the rectangle to relieve some of the pressure from your saw.[3]

    • Wear safety glasses when drilling the holes to prevent sawdust from getting in your eyes.
  4. 4

    Cut out the rectangle using a jigsaw. Put the blade of the saw through one of the holes you lot just drilled. Turn on your saw to a medium speed and slowly follow the outline yous drew on your overhang. Don't stand direct under the saw or else the woods could autumn on yous after y'all make your final cut.[four]

    • Finish in the holes y'all drilled if you need to adjust the direction y'all're cutting.
  5. v

    Screw in a 8 in × 16 in (20 cm × 41 cm) vent to embrace the hole. Use wood screws to hold the vents in identify. Agree the soffit vent over the opening with your non-dominant hand and use a drill with a screwdriver scrap to secure it. Kickoff with the corner screws before adding the others.[five]

    • Virtually vents volition have 4-6 holes to add screws.
  6. half-dozen

    Place soffits every 4 ft (1.2 one thousand) forth your overhang if needed. Measure the altitude between from the soffit vent you just installed to add together more than. You should have ane square human foot (0.093 m2) of ventilation for every 300 square feet (28 mii) in your home. Repeat the process for each vent you lot want to install.[vi]

    • Aim to have a 50/50 balance betwixt intake vents and exhaust vents.
    • Place a layer of window screen inside your vents to keep out rodents or insects.

    Advertisement

  1. 1

    Bulldoze a blast through your cranium to mark where you desire your vent. Go into your attic and find a spot at least two feet (0.61 m) down from the acme of your roof. Utilise a hammer to pound a nail through to the roof. The nail will either visibly stick out from the roof or raise shingles and then you know where it is.[seven]

    • Brand sure the smash is in between the rafters then y'all tin fit the vent between them.
    • If you don't have the room to swing a hammer, use a drill and a long screw.
  2. 2

    Clear the shingles in the area to make room for the vent. Get on your roof using a ladder and locate the blast. Utilize a hook hammer to loosen and remove the shingles around the nail to clear a infinite equal to the opening on the bottom of the vent. Otherwise, cut out the shingles using a utility knife. In one case yous're finished, draw a foursquare outline the same size as your vent on the roof.[8]

    • Only get on your roof if you're comfy doing information technology. Otherwise, rent a professional person roofing service to come install the vents for you.
  3. three

    Use a circular or reciprocating saw to cut through your roof. Ready the saw depth so it only cuts through the pinnacle of your roof and not any rafters. Turn the saw on and follow along with your outline until the foursquare is completely cut out. Lift the boards out or push them into your attic to throw away later.[9]

    • Article of clothing protective heart gear to prevent getting sawdust in your eyes.
    • Yous can saw through your shingles and roofing at the same time if you accept a roofing cutting blade for your saw. The flanges on your vent should slide underneath the surrounding shingles easily.
  4. 4

    Identify a layer of roofing tar or caulk around the hole and press the vent down. Use a caulk gun to squeeze out an even layer of the agglutinative around the edges of the hole. Set your vent on top of the hole so it lines up and press information technology down so it adheres completely.[10]

    • Roofing tar and caulk can be purchased in an piece of cake applicator tube at your local hardware or domicile improvement store.
  5. 5

    Secure the vent in place with nails. Nail downward the corners of the vent first to keep it in place. Add together more nails forth the sides every iv–5 in (10–13 cm) so information technology doesn't come loose.[11]

    • Some vents will have holes where you tin place nails, but some volition non.
  6. 6

    Glue down shingles to cover the bottom of the vent. Place a line of roofing tar or caulk on top of the vent's flange, or its bottom flap, using a caulk gun. Printing new shingles onto the caulk and use nails at the meridian of each shingle to fully secure them to the roof. Cover the entire flange with shingles to integrate it amend into the roof.[12]

    • Cut the shingles to fit effectually the vent with a utility knife if you need to.

    Ad

  1. 1

    Remove the cap shingles from the peak of your roof. The cap shingles are shaped similar upside-down V's and establish at the meridian of your roof. Become onto your roof using a tall ladder and climb to the top. Pry up the shingles forth the summit of your roof using a claw hammer. Set them bated and then you can utilise them later instead of throwing them away.[13]

    • Be conscientious on your roof if it has a steep slope.
    • Hire a professional person roofing service if you're uncomfortable climbing on the top of your roof.
  2. 2

    Cutting a slot going 3four  in (i.9 cm) down from both sides of the peak. Set the depth of a circular saw then it doesn't cut through the rafters in your attic. Push the circular saw in a directly line across the entire peak of your roof to make a slot for your ridge vent. Once you lot've finished sawing, remove the droppings from your roof.[14]

    • Ridge vents can go across the entire length of your roof or placed in sections the aforementioned length every bit the vent. Cutting the slots according to how you want the vent.
  3. iii

    Set the ridge vents on peak of the slot. Apply enough vent pieces to fill the length of the slot you lot cut. Eye the vents on the superlative of your roof so the sides of the vent lay flat on the roof. If yous demand to cut the vent to fit at the end of your roof, employ a utility knife to brand information technology flush with your home. Concur the vent slice in place until yous can nail it down.[fifteen]

    • Bank check your local hardware or domicile comeback shop to run across if they have ridge vents available.
    • Employ ridge vents meant for the pitch of your roof.
  4. iv

    Nail the vents to secure them in place. Utilize the pre-drilled holes in the vents for your nails. Make certain the nails are long enough to go through the vent and into your roof. Drive them in with a hammer so the vents are tight confronting the roof.[16]

  5. 5

    Supersede the cap shingles on acme of the ridge vent. Layer the cap shingles on pinnacle of the vent and nail them through your vent to keep them in identify. Make sure the nails accomplish down into the roof and then they don't blow away in harsh weather.[17]

    • This step is optional but if you lot desire to blend the vent into the balance of your roof.

    Advertisement

Add New Question

  • Question

    How many roof vents exercise I need?

    David Bitan

    David Bitan
    Roofing Contractor & Maintenance Professional person

    David Bitan is a roofing professional, licensed contractor, and the owner and founder of Bumble Covering based in Southern California. With over 12 years of construction industry feel, David specializes in restoring, repairing, and maintaining residential, commercial, and industrial roofs. With over 60 years of combined experience, Bumble Covering provides easy, friendly services to structures including residential, commercial, industrial, multi-family, and authorities buildings along with hospitals, hotels, and churches.

    David Bitan

    Roofing Contractor & Maintenance Professional

    Expert Answer

  • Question

    Can I install roof vents myself?

    David Bitan

    David Bitan
    Covering Contractor & Maintenance Professional

    David Bitan is a roofing professional person, licensed contractor, and the owner and founder of Bumble Covering based in Southern California. With over 12 years of construction industry experience, David specializes in restoring, repairing, and maintaining residential, commercial, and industrial roofs. With over sixty years of combined experience, Bumble Roofing provides easy, friendly services to structures including residential, commercial, industrial, multi-family, and authorities buildings along with hospitals, hotels, and churches.

    David Bitan

    Roofing Contractor & Maintenance Professional

    Proficient Answer

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

  • Apply roofing jacks to concord a board on the roof so you have a place to proceed you and your tools from slipping off. Look at your local hardware or home comeback store for them.

Advertisement

  • Don't work on your roof during choppy or severe weather condition.

Advertizing

Things Yous'll Need

  • Pencil
  • Straightedge
  • Drill
  • Jigsaw
  • Soffit vents
  • Wood screws
  • Claw hammer
  • Nails
  • Ladder
  • Utility knife
  • Round or reciprocating saw
  • Caulk gun
  • Static vent
  • Roofing cement
  • Ladder
  • Claw hammer
  • Circular saw
  • Ridge vents
  • Nails

Most This Article

Article Summary 10

To install a roof vent, commencement by installing air vents along the edges of your attic, which volition allow the moisture to escape from your home. Adjacent, find a spot on the roof for your exhaust vent, depict a square outline the aforementioned size as your vent, and remove the shingles from that expanse. Then, use a circular saw to cut into the area yous marked, and squeeze out a line of caulk around the edges of the hole to help the vent stick to the roof. Finally, position your frazzle vent on acme of the hole, and nail downward the corners to ensure that it stays in place. To learn more, like how to alloy the vent into the remainder of your roof, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 269,733 times.

Did this article help you lot?

Source: https://www.wikihow.com/Install-a-Roof-Vent

Posted by: hollandtheres.blogspot.com

0 Response to "How To Install A Register Vent"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel